Lantech IPES-5208T (IP54/IP67) is a high performance L2+ (Gigabit uplink) switch with 8 10/100TX (D-coded) + 2 10/100/1000T(X-coded) w/8 PoE 802.3af/at Injectors by M12 provides L2 wire speed and advanced security function for network aggregation deployment It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring while also supports train ring, enhanced mode , multiple VLAN mode with easy configuration. The comprehensive QoS, QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, TACACS+*, SSH/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ* are supported and also required in large network. It also supports Cisco Discovery Protocol (CDP) for Ciscoworks to detect the switch info and show on L2 map topology.
PoE +, Advanced PoE management
Lantech IPES-5208T(IP54) supports IEEE802.3at/af standard which can feed HI-power up to 30W at each PoE port for big power consumption devices like PTZ IP camera, High power wireless AP etc. The advanced PoE management includes PoE detection and scheduling besides the regular PoE per port status. PoE detection can detect if the connected PD hangs then restart the PD; PoE scheduling is to allow pre-set power feeding schedule upon routine time table. Per port PoE status can remotely On/Off the power and display information of voltage, current, watt and PoE temperature.
Dual power Input: 12V model, 72V model and 110V model;
The Lantech IPES-5208T (IP54/IP67) series is designed with various dual power input at 12/24/48VDC input (12V model), 72V input to feed 54V PoE (72V model). The 110V model can accept dual 110V to feed 54V POE at PoE budget max 80W. Featured with relay contact alarm function, the IPES-5208T (IP54/IP67) is able to connect with alarm system in case of power failure or port disconnection events
Miss-wiring avoidance, Repowered auto ring restore, Loop protection
The IPES-5208T (IP54/IP67) also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech IPES-5208T (IP54/IP67) is able to alert with the LED indicator and disable ring automatically. Repowered auto ring restore function (node failure protection) ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.
DHCP option 82 & Port based, Mac based DHCP, Option66, IPv6 DHCP server**
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Option66 server can offer IP address of TFTP server to DHCP client for VOIP application. Optional IPv6 address resolution for DHCP service can be supported.
User friendly GUI, Auto topology drawing
The user friendly UI, innovative auto topology drawing and topology demo makes IPES-5208T (IP54/IP67) much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.
Enhanced G.8032 ring, 16 MSTI MSTP; Optional MRP ring
Lantech IPES-5208T (IP54/IP67) features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering Multicast packets. It also supports various ring topologies that covers double ring, multi-chain (under enhanced ring), train ring, basic ring, multiple-VLAN ring and auto-ring by easy setup than others. The innovative auto-Ring configurator (auto mode) can calculate owner and neighbor in one step. It supports MSTP that allows each spanning tree for each VLAN for redundant links with 16 MSTI.
Optional MRP (Media Redundancy Protocol) can be supported for industrial automation networks.
Editable configuration file
Optional N key auto backup, Exported text file
The configuration file of Lantech IPES-5208T (IP54/IP67) can be exported in text file so that it can be edited and configured back to switch with ease for mass deployment.
The optional N-key configurator offers firmware upgrade, auto/editable configuration back up and restoration without computer by adjusting the DIP switch.
QoS by VLAN for legacy device
QoS by VLAN can allow switch to tag QoS by VLAN regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.
QinQ**, QoS QinQ** and GVRP** supported
It supports the QinQ**, QoS QinQ**, GVRP** for large VLAN segmentation.
IGMPv3, GMRP**, router port, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP**, router port and static multicast forwarding binding by ports for video surveillance application.
Event log & message; 1 DI + 1 DO
In case of event alarm, the IPES-5208T-X (IP54) is able to send an email & SMS** text message to pre-defined addresses as well as SNMP Traps out immediately. It provides 1DI and 1DO while disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.
Environmental monitoring for inside switch information
The built-in environmental monitoring can detect switch overall temperature, voltage, current and total PoE load where can send the SNMP traps, email and SMS** alert when abnormal.
EN50155, EN45545-2, EN61373 verification; High ESD protection
Lantech IPES-5208T(IP67/IP54) features high reliability and robustness coping with extensive EMI/RFI phenomenon, environmental vibration and shocks usually found in factory, substation, steel automation, aviation, mining and process control. It is the best solution for Automation, transportation, surveillance, Wireless backhaul, Semi-conductor factory and assembly lines.
The IPES-5208T (IP54/IP67) is designed to meet with critical network environment with IP67/IP54 aluminum enclosure and M12 connectors for water proof. With EN45545-2 Fire & Smoke, and EN50155 & EN61373 verification, the IPES-5208T (IP67/IP54) is best for railway in train/track side, vehicle and mining applications. For more usage flexibilities, IPES-5208T (IP54/IP67) supports wide operating temperature from -40°C to 75°C.
IPES-5208T (IP54/IP67)also provides ±2000V EFT and ±6000V ESD contact protection, which can reduce unstable situation caused by power line and Ethernet.
Optional bypass protection
The optional bypass relay is set to bypass the switch to the next one when power is off in order to protect the network from crashing. Lantech bypass caters to remain in bypass mode until the switch is completely booting up when power is back to avoid another network lost. The bypass is also activated when detecting the CPU watchdog is ON.
|8360-83019||IPES-5208T-X-54-12V||8 10/100TX PoE at/af up to 30W + 2 10/100/1000T X-coded EN50155 M12 IP54 L2+ PoE Managed Ethernet Switch; 9V~56V dual input; -40°C to 75°C|
|8360-83119||IPES-5208T-X-54-72V||8 10/100TX PoE at/af up to 30W + 2 10/100/1000T X-coded EN50155 M12 IP54 L2+ PoE Managed Ethernet Switch; 50.4~90V dual input; -40°C to 60°C|
|8360-83219||IPES-5208T-X-54-110V||8 10/100TX PoE at/af up to 30W + 2 10/100/1000T X-coded EN50155 M12 IP54 L2+ PoE Managed Ethernet Switch; 43~137.5V dual input; -40°C to 60°C|
|8360-83319||IPES-5208T-X-67-12V||8 10/100TX PoE at/af up to 30W + 2 10/100/1000T X-coded EN50155 M12 IP67 L2+ PoE Managed Ethernet Switch; 9V~56V dual input; -40°C to 75°C|
|8360-83419||IPES-5208T-X-67-72V||8 10/100TX PoE at/af up to 30W + 2 10/100/1000T X-coded EN50155 M12 IP67 L2+ PoE Managed Ethernet Switch; 50.4~90V dual input; -40°C to 60°C|
|8360-83519||IPES-5208T-X-67-110V||8 10/100TX PoE at/af up to 30W + 2 10/100/1000T X-coded EN50155 M12 IP67 L2+ PoE Managed Ethernet Switch; 43~137.5V dual input; -40°C to 60°C|
|8850-100||N-key Configurator||RJ45 connector dongle for firmware upgrade, auto/editable configuration backup and restoration; -20°C to 60°|
|ECONM23-5P(F)70CM CABLE||M23 power cable 90 degree angle, 70cm, 5 pin, Made in Taiwan|
|ECONM23-5P(F)70CM CABLE-C||M23 power cable 90 degree angle, 70cm, 5 pin, Made in China|
|ECAB124030MJS||4 Pin M12 RJ45 Male 3 Meters; STP Cable|
|ECABM12X83MSTP||8 Pin M12 X-coded RJ45 Male 3 METER, STP CABLE w/ Shielding|