Lantech IGS-5416MGSFP is a high performance L2+ (All Gigabit) switch with 16 10/100/1000T + 4 1G/2.5G SFP which provides L2 wire speed and advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring. It also supports train ring*, enhanced mode with easy configuration, comprehensive QoS, QoS by VLAN**, advanced security including INGRESS ACL L2/L3, TACACS+, SSH v2/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ which are important features required in large network. The Cisco Discovery Protocol (CDP) and LLDP are supported for Ciscoworks to detect the switch info and show on L2 map topology. The enhanced platform allows quick booting up time under 50 seconds.
Miss-wiring avoidance, Loop protection, Node failure protection
The IGS-5416MGSFP also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech IGS-5416MGSFP is able to alert with the LED indicator and disable ring automatically. Node failure protection ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. This feature prevents the broken ring and keep ring alive without any re-configuration needed. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.
DHCP option 82 & Port based, Mac based DHCP, Option66, DHCP Snooping, IPv6 DHCP server
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Snooping is supported. For the ending device which need to download file from TFTP server, DHCP Option66 server can offer IP address of TFTP server to DHCP client. Basic IPv6 DHCP service can be supported.
User friendly GUI, Auto topology drawing
The user friendly UI, innovative auto topology drawing and topology demo makes IGS-5416MGSFP much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.
Enhanced G.8032 ring, 8 MSTI MSTP; MRP ring
Lantech IGS-5416MGSFP features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering multicast packets. It also supports various ring topologies that covers enhanced ring and basic ring by easy setup than others. It supports MSTP that allows RSTP over VLAN for redundant links with 8 MSTI. MRP (Media Redundancy Protocol) can be supported for industrial automation networks.
QoS by VLAN** for legacy device
QoS by VLAN** can allow switch to tag QoS by VLAN** regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.
QinQ, QoS and GVRP supported
It supports the QinQ, QoS, GVRP for large VLAN segmentation.
IGMPv3, GMRP, router port, MLD Snooping, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP, router port, MLD snooping and static multicast forwarding binding by ports for video surveillance application.
Enhanced Storm Control
Storm control prevents traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on one of the physical interfaces and the detection is more precise and reaction is more efficient.
Editable configuration file
The configuration file of Lantech IGS-5416MGSFP can be exported and edited with word processor for the other switches configuration with ease. The factory reset button can restore the setting back to factory default The built-in watchdog design can automatically reboot the switch when CPU is found dead. IGS-5416MGSFP also supports dual image firmware function.
The built-in USB port can upload/download the firmware through USB dongle for switch replacement.
2DI/2DO for relay contact and event alerting by email & traps
In case of event, the IGS-5416MGSFP is able to send an email to pre-defined addresses as well as SNMP Traps out immediately. It provides 2DI and 2DO. When disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.
Enhanced Environmental monitoring for Ethernet switch inside information
The enhanced environmental monitoring can detect switch overall temperature, actual input voltage and current. It also can send the SNMP traps and email** when abnormal.
24V/HV isolated input voltage selection: dual 12~60VDC (24V model) or single 90~305VAC/120~430VDC (HV model)
The Lantech IGS-5416MGSFP is able to work at dual 12~60VDC (24V model). Or with single high power supply at 90~305VAC / 120~430VDC (HV model).
Industrial hardened design with high EFT and ESD protection
Lantech IGS-5416MGSFP features high reliability and robustness coping with extensive EMI/RFI phenomenon, environmental vibration and shocks usually found in factory, substation, steel automation, aviation, mining and process control. Featured with relay contact alarm function, the IGS-5416MGSFP is able to connect with alarm system in case of power failure or port disconnection. The IGS-5416MGSFP also provides ±2000V EFT/SURGE and ±4000 VDC (Contact) / ±8000 VDC (Air) Ethernet ESD protection, which can reduce unstable situation caused by power line and Ethernet.
It is the best solution for Automation, transportation, surveillance, Wireless backhaul, Semi-conductor factory applications. The -E model can be used in extreme environments with an operating temperature range of -40°C to 75°C.
|8350-8761||IGS-5416MGSFP-24V||16 10/100/1000T + 4 1G/2.5G SFP L2+ Industrial Managed Ethernet Switch; -20°C to 60°C; Enhanced Environmental Monitoring; dual 12~60VDC input|
|8350-877||IGS-5416MGSFP-24V-E||16 10/100/1000T + 4 1G/2.5G SFP L2+ Industrial Managed Ethernet Switch; -40°C to 75°C; Enhanced Environmental Monitoring; dual 12~60VDC input|
|8350-878||IGS-5416MGSFP-HV||16 10/100/1000T + 4 1G/2.5G SFP L2+ Industrial Managed Ethernet Switch; -20°C to 60°C; Enhanced Environmental Monitoring; single high power 90~305VAC / 120~430VDC|
|8350-879||IGS-5416MGSFP-HV-E||16 10/100/1000T + 4 1G/2.5G SFP L2+ Industrial Managed Ethernet Switch; -40°C to 75°C; Enhanced Environmental Monitoring; single high power 90~305VAC / 120~430VDC|
|9000-114||OS3 – L3L||OS3 software platform with Layer 3 Lite functions (please check Lantech software data sheet for details)|
|9000-116||OS3 – L3*||OS3 software platform with Layer 3 functions incl. L3L (please check Lantech software data sheet for details)|
|MDR-40 Series||40W Single Output Industrial Din Rail Power; 85-264VAC / 120-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 4% per degree from 60°C ~ 70°C)|
|MDR-20 Series||20W Single Output Industrial Din Rail Power; 85-264VAC / 120-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C)|
|Model name||Description||Model name||Description|
|8330-162X||MINI GBIC 1000SX (LC/0.5km) Transceiver||8330-186||LTSFP-1000BX-20KM Transceiver (WDM 1310)|
|8330-163X||MINI GBIC 1000SX2 (LC/2km) Transceiver||8330-187||LTSFP-1000BX-20KM Transceiver (WDM 1550)|
|8330-165X||MINI GBIC 1000LX (LC/10km) Transceiver||8330-180||LTSFP-1000BX-40KM Transceiver (WDM 1310)|
|8340-0591||MINI GBIC 1000LHX (LC/40km) Transceiver||8330-182||LTSFP-1000BX-40KM Transceiver (WDM 1550)|
|8330-166||MINI GBIC 1000XD (LC/50km) Transceiver||8330-181||LTSFP-1000BX-60KM Transceiver (WDM 1310)|
|8330-169||MINI GBIC 1000XD (LC/60km) Transceiver||8330-183||LTSFP-1000BX-60KM Transceiver (WDM 1550)|
|8330-167||MINI GBIC 1000ZX (LC/80km) Transceiver||8330-184||LTSFP-1000BX-80KM Transceiver (WDM 1490)|
|8330-170||MINI GBIC 1000EZX (120km) Transceiver||8330-185||LTSFP-1000BX-80KM Transceiver (WDM 1550)|
|8330-168||MINI GBIC 1000T (100m) Transceiver||8330-262D||MINI GBIC 2.5G 850nm VCSEL (LC/0.3km) Transceiver|
|8330-188||LTSFP-1000BX-10KM Transceiver (WDM 1310)||8330-263D||MINI GBIC 2.5G 1310nm FP (LC/2km) Transceiver|
|8330-189||LTSFP-1000BX-10KM Transceiver (WDM 1550)||8330-265D||MINI GBIC 2.5G 1310nm DFB (LC/15km) Transceiver|
|All SFP P/N# ended with D are with DDM function|