Lantech IES-5408T (IP67/IP54) is a high performance L2+ (Gigabit uplink) switch with 8 10/100TX(D-coded) + 4 10/100/1000T(X-coded) M12 provides L2 wire speed and advanced security function for network aggregation deployment. It delivers ITU G.8032 enhanced ring recovery less than 20ms in single ring while also supports train ring, enhanced mode, multiple VLAN mode with easy configuration. The comprehensive QoS, QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, TACACS+*, SSH/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ** are supported and also required in large network. It also supports Cisco Discovery Protocol (CDP) for Ciscoworks to detect the switch info and show on L2 map topology.
Various dual input voltage selection of 12V/72V/110V
Lantech IES-5408T (IP67/IP54) is designed with various selection of dual input power voltage for 12V/72V/110V. 12V model can accept 9V~60VDC dual input power; 72V model for 50.4V~90VDC dual input range and 110V model for 43V~137.5V. The unique WV model can allow 16.8V~137.5V dual input range. Featured with relay contact alarm function, the IES-5408T (IP67/IP54) is able to connect with alarm system in case of power failure or port disconnection events.
Miss-wiring avoidance, Loop protection, Auto re-powered ring restore
The IES-5408T (IP67/IP54) also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech IES-5408T (IP67/IP54) is able to alert with the LED indicator and disable ring automatically. Repowered auto ring restore function (node failure protection) ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.
DHCP option 82 & Port based, Mac based DHCP, Option66, IPv6 DHCP server**
DHCP server can assign dedicated IP address by MAC or by port (Port based for single switch) , it also can assign IP address by port for multiple switches with single DHCP option82 server. DHCP Option66 server can offer IP address of TFTP server to DHCP client for VOIP application. Optional IPv6 address resolution for DHCP service can be supported.
User friendly UI, Auto topology drawing, complete CLI
The user friendly UI, innovative auto topology drawing and topology demo makes IES-5408T (IP67/IP54) much easier to get hands-on. The complete CLI enables professional engineer to configure setting by command line.
Enhanced G.8032 ring; 16 MSTI MSTP; Optional MRP ring
Lantech IES-5408T (IP67/IP54) features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering Multicast packets. It also supports various ring topologies that covers double ring, multi-chain (under enhanced ring), train ring, basic ring, multiple-VLAN ring and auto-ring by easy setup than others. The innovative auto-Ring configurator (auto mode) can calculate owner and neighbor in one step. It supports MSTP that allows each spanning tree for each VLAN for redundant links with 16 MSTI.
QoS by VLAN for legacy devices to tag with priority
QoS by VLAN can allow switch to tag QoS by VLAN regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.
QinQ**, QoS QinQ** and GVRP** supported
It supports the QinQ**, QoS QinQ**, GVRP** for large VLAN segmentation.
IGMPv3, GMRP**, router port, static multicast forwarding and multicast Ring protection
The unique multicast protection under enhanced G.8032 ring can offer immediate self-recovery instead of waiting for IGMP table timeout. It also supports IGMPv3, GMRP**, router port and static multicast forwarding binding by ports for video surveillance application.
Editable configuration file
Optional N key auto backup, Exported text file
The configuration file of Lantech IES-5408T (IP67/IP54) can be exported in text file so that it can be edited and configured back to switch with ease for mass deployment. The optional N-key configurator offers firmware upgrade, auto/editable configuration back up and restoration without computer by adjusting the DIP switch.
Event log & message; 1 DI + 1 DO
In case of event, the IES-5408T (IP67/IP54) is able to send an email & SMS** text message to pre-defined addresses as well as SNMP Traps out immediately. It provides 1DI and 1DO. When disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.
Built-in environmental monitoring to show switch inside info
The built-in environmental monitoring can detect switch overall temperature, voltage and current where can send the SNMP traps, email and SMS** alert when abnormal.
EN50155, EN45545-2, EN61373 verification; High ESD protection
Lantech IES-5408T (IP67/IP54) features high reliability and robustness coping with extensive EMI/RFI phenomenon, environmental vibration and shocks usually found in factory, substation, steel automation, aviation, mining and process control. It is the best solution for Automation, transportation, surveillance, Wireless backhaul, Semi-conductor factory and assembly lines.
The IES-5408T (IP67/IP54) is designed to meet with critical network environment with IP67/IP54 aluminum enclosure and M12 connectors for water proof. With EN45545-2 Fire & Smoke, and EN50155 & 61373 verification, the IES-5408T (IP67/IP54) is best for railway in train/track side, vehicle and mining applications. For more usage flexibilities, IES-5408T (IP67/IP54) supports wide operating temperature from -40°C to 75°C.
IES-5408T (IP67/IP54) also provides ±2000V EFT and ±6000V ESD contact protection, which can reduce unstable situation caused by power line and Ethernet.
Optional bypass relay prevent from power lost
The optional bypass relay is set to bypass the switch to the next one when power is off in order to protect the network from crashing. Lantech bypass caters to remain in bypass mode until the switch is completely booting up when power is back to avoid another network lost. The bypass is also activated when detecting the CPU watchdog is ON. (IP67 only)
|8360-715||IES-5408T-X-67-12V||8 10/100TX + 4 GigaT EN50155 M12 IP67 L2+ Managed Ethernet Switch; -40°C to 75°C; dual 9~56VDC|
|8360-7151||IES-5408T-X-54-12V||8 10/100TX + 4 GigaT EN50155 M12 IP54 L2+ Managed Ethernet Switch; -40°C to 75°C; dual 9~56VDC|
|8360-718||IES-5408T-X-67-72V||8 10/100TX + 4 GigaT EN50155 M12 IP67 L2+ Managed Ethernet Switch; -40°C to 60°C; dual 50.4~90VDC|
|8360-7181||IES-5408T-X-54-72V||8 10/100TX + 4 GigaT EN50155 M12 IP54 L2+ Managed Ethernet Switch; -40°C to 60°C; dual 50.4~90VDC|
|8360-753||IES-5408T-X-67-110V||8 10/100TX + 4 GigaT EN50155 M12 IP67 L2+ Managed Ethernet Switch; -40°C to 60°C; dual 43~137.5VDC|
|8360-7532||IES-5408T-X-54-110V||8 10/100TX + 4 GigaT EN50155 M12 IP54 L2+ Managed Ethernet Switch; -40°C to 60°C; dual 43~137.5VDC|
|8360-719||IES-5408T-X-67-WV||8 10/100TX + 4 GigaT EN50155 M12 IP67 L2+ Managed Ethernet Switch; -40°C to 60°C; dual 16.8~137.5VDC|
|8360-7191||IES-5408T-X-54-WV||8 10/100TX + 4 GigaT EN50155 M12 IP54 L2+ Managed Ethernet Switch; -40°C to 60°C; dual 16.8~137.5VDC|
|8850-100||N-key Configurator||RJ45 connector dongle for firmware upgrade, auto/editable configuration backup and restoration; -20°C to 60°|
|ECONM23-5P(F)70CM CABLE||M23 power cable 90 degree angle, 70cm, 5 pin, Made in Taiwan|
|ECONM23-5P(F)70CM CABLE-C||M23 power cable 90 degree angle, 70cm, 5 pin, Made in China|
|ECONM23-5P(F)S-90||M23 5Pin female 90 degree screw type connector|
|ECONM23-5P(F)S-180||M23 5Pin female 180 degree screw type connector|
|ECAB124030MJS||4 Pin M12 RJ45 Male 3 Meters; STP Cable|
|ECABM12X83MSTP||8 Pin M12 X-coded RJ45 Male 3 METER, STP CABLE w/ Shielding|