Logo-of-Lantech

SFP+ 10Gbps (10KM)

10G SFP+ LR Transceiver

  • Hot Pluggable, Duplex LC, 1310nm DFB-LD, Single Mode, DDM
  • Distance: 10KM
  • Standard Operating Temperature: -10°C ~ 70°C
  • Wide Operating Temperature: -40°C ~ 85°C


FCC CE WEEE RoHS2


Datasheet

OVERVIEW

10GBase SFP+ LR Small Form Factor Pluggable SFP+ transceivers are compliant with the current SFP+ Multi-Source Agreement (MSA) Specification. The high Performance uncooled 1310nm DFB transmitter and high sensitivity PIN receiver provide superior performance for 10GBase-LR/LW applications up to 10km optical links.


FEATURES

  • Compliant with IEEE802.3ae 10GBase-LR Ethernet Standard
  • Compliant with SFF8472 diagnostic monitoring interface
  • 1310nm DFB laser transmitter.
  • Duplex LC connector
  • 2-wire interface for management and diagnostic monitor
  • Single +3.3V power supply voltages
  • Transmission distance of 10km over single mode fiber
  • RoHS Compliant Part

SPECIFICATIONS

Absolute Maximum Ratings

Parameter

Symbol

Min.

Max.

Unit

Note

Storage Temperature

Ts

-40

+85

°C

 

Operating Temperature

Top

-10

+70

°C

 

Supply Voltage

Vcc

-0.5

+4.0

V

 

  Storage Relative Humidity

RH

5

95

%

 

  Operational Humidity

RH

0

85

%

 

Recommended Operating Conditions

Parameter

Symbol

Min.

Typ.

Max.

Unit

Note

Case Operating Temperature

Top

-10

 

+70

°C

1

Supply Voltage

Vcc

+3.15

+3.3

+3.46

V

 

Supply Current

Icc

 

250

300

mA

 

Notes:  1. Standard Operating Temperature / Wide Operating Temperature (-E model)

Transmitter Electro-Optical Characteristics

Parameters

Symbol

Min.

Typ.

Max.

Unit

Note

Operating Date Rate

DR

9.953

10.3125

 

Gb/s

 

Bit Error Rate

BER

 

 

10-12

 

 

Optical Launch Power

Po

-8.2

 

+0.5

dBm

1

Optical Launch Power (OMA)

Po-OMA

-5.2

 

 

dBm

1

Center Wavelength

λ

1260

1310

1355

nm

 

Spectral Width (-20dB)

△λ

 

 

1

nm

 

Side Mode Suppression Ratio

SMSR

30

 

 

dB

 

Optical Extinction Ratio

ER

3.5

 

 

dB

 

Average Launch power of OFF Transmitter

POFF

 

 

-30

dBm

 

Optical Eye Mask

IEEE802.3ae

 

Relative Intensity Noise

RIN

 

 

-128

dB/Hz

 

Differential data input voltage

VDIFF

120

 

1200

mV

 

Transmit Disable Voltage

Vdis

2.0

 

Vcc

V

 

Transmit Enable Voltage

Ven

Vee

 

Vee+0.8

V

 

Notes: 1. The optical power is launched into a 9/125μm single-mode fiber

Receiver Electro-Optical Characteristics

Vcc= 3.15V to 3.46V, Top = -10 C to 70 C

Parameters

Symbol

Min.

Typ.

Max.

Unit

Note

Operating Date Rate

DR

9.953

10.3125

 

Gb/s

 

Receiver Sensitivity

PIN_min

  

 

-14.4

dBm

1

Maximum Input Power

PIN_max

 

 

+0.5

dBm

1

Optical Center Wavelength

λC

1200

1310

1600

nm

 

Receiver Reflectance

RR

 

 

-14

dB

 

LOS De-Assert

LOSD

 

 

-15

dBm

 

LOS Assert

LOSA

-30

 

 

dBm

 

LOS Hysteresis

LOSHY

0.5

 

 

dB

 

Differential data output voltage

Vout,pp

500

 

800

mV

 

Data Output Rise/Fall Time (20%~80%)

Tr/Tf

 

 

30

ps

 

Receiver LOS Signal Output Voltage-Low

LOSVL

Vee

 

0.5

V

 

Receiver LOS Signal Output Voltage-High

LOSVH

2.4

 

Vcc

V

 

Note1: Measured with a PRBS 231-1 test pattern @10.3125Gbps BER<10-12

Pin Assignment


Diagram of Host Board Connector Block Pin Numbers and Name

Pin Description

Pin

Name

Function / Description

1

VeeT

Transmitter Ground

2

TX_Fault

Transmitter Fault Indication (1)

3

TX_Disable

Transmitter Disable – Turns off transmitter laser output (2)

4

SDA

2-wire Serial Interface Data Line (SDA: Serial Data Signal) (3)

5

SCL

2-wire Serial Interface Clock (SCL: Serial Clock Signal) (3)

6

Mod_ABS

Module Absent, connected to VeeT or VeeR in the module (3)

7

RS0

Rate Select 0, optionally controls SFP+ module receiver (5)

8

Rx_LOS

Receiver Loss of Signal Indication (4)

9

RS1

Rate Select 1, optionally controls SFP+ module transmitter (5)

10

VeeR

Receiver Ground

11

VeeR

Receiver Ground

12

RD-

Receiver Inverted Data output, Differential LVPECL, AC coupled

13

RD+

Receiver Non-Inverted Data output, Differential LVPECL, AC coupled

14

VeeR

Receiver Ground

15

VccR

Receiver 3.3V Power Supply

16

VccT

Transmitter 3.3V Power Supply

17

VeeT

Transmitter Ground

18

TD+

Transmitter Non-Inverted Data Input, Differential LVPECL, AC coupled

19

TD-

Transmitter Inverted Data Input, Differential LVPECL, AC coupled

20

VeeT

Transmitter Ground

Note1: TX Fault is open collector/drain output which should be pulled up externally with a 4.7K~ 10KΩ resistor on the host board to supply <VccT+0.3V or VccR+0.3V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to <0.8V.
Note2: TX Disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a 4.7K~10KΩ resistor. 1)Low(0~0.8V): Transmitter on; 2)Between(0.8V and 2V): Undefined; 3)High (2.0~ VccT): Transmitter Disabled; 4)Open: Transmitter Disabled
Note3: These are the module definition pins. They should be pulled up with a 4.7K~10KΩ resistor on the host board to supply less than VccT+0.3V or VccR+0.3V. Mod-ABS is grounded by the module to indicate that the module is present.
Note4: LOS (Loss of signal) is an open collector/drain output which should be pulled up externally with a 4.7K~10KΩ resistor on the host board to supply <VccT+0.3V or VccR+0.3V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to <0.8V.

Note5: No connect on this module.

Digital Diagnostic Functions

As defined by the SFP MSA (SFF-8472) Lantech’s SFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters:

  • Transceiver temperature
  • Laser bias current
  • Transmitted optical power
  • Received optical power
  • Transceiver supply voltage

It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range.

The operating and diagnostics information is monitored and reported by a Digital Diagnostics Controller (DDC) inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially.

Digital Diagnostic Memory Map

Digital Diagnostic Monitoring Characteristics Map

Parameter

Accuracy

Unit

Note

Temperature

±3

℃

 

Supply Voltage

±0.1

V

 

TX Bias Current

±5

mA

 

TX Output Power

±3

dB

 

RX Received Optical Power

±3

dB

 

DIMENSION

*All dimensions are ±0.2mm unless otherwise specified

ORDERING INFORMATION

Part Number

TX

RX

Link

DDM

Mode

Temp.

8330-194D-V1

1310nm

1310nm

10km

Yes

Single-mode

-10~70°C

8330-194DE-V1

1310nm

1310nm

10km

Yes

Single-mode

-40~85°C

About Lantech

IRIS-ISO-and-ITxPT-LOGO
Lantech is an IRIS / IEC62443-4-1 certified company as well as a member of ITxPT. Lantech designs and produces a complete family of industrial networking products. For decades, Lantech has provided professional and powerful industrial networking solutions globally. Learn More

Taiwan Quality

Lantech-provides-Taiwan-quality-products-and-proudly-provide-5-years-warranty-to-our-industrial-products Lantech is dedicated to providing the best quality and service to our customers. We proudly provide 5 years warranty to our industrial products. Learn More

Contact Us

7F, No.33, Sec.1, Tiding Blvd.,
Neihu District, Taipei, Taiwan, 114066 (or 11494)
Phone: +886-2-2790-2589 │ Fax: +886-2-2790-2516
Email: info@lantechcom.tw
Product Inquiry Form

2020 © Lantech Communications Global, Inc. ALL Rights Reserved. Privacy Policy | Terms of Service

Logo-of-Lantech