8 10/100TX + 4 100FX L2+ Industrial Managed Switch

  • IEC 61850-3 & IEEE1613 compliance
  • Goose monitoring; Built-in MMS server for power SCADA
  • Enhanced G.8032 ring protection < 20ms for single ring. Supports auto mode, enhanced mode, train mode and basic mode; Enhanced G.8032 ring covers multicast packets; MSTP 8/16* MSTI /RSTP
  • Miss-wiring avoidance & Repowered auto ring restore (node failure protection)
  • User friendly UI, including auto topology drawing and DDM threshold monitoring with dB values***; Complete CLI
  • Support LACP link aggregation, IGMP v3/router port, DHCP server & DHCP Option82 for Port/Vlan based DHCP distribution, Mac based DHCP server, QoS by VLAN, SSH/SSL, HTTPS, INGRESS/EGRESS ACL L2/L3, IPv6, SMS
  • Environmental Monitoring for temp., voltage & current
  • 1500VDC Isolated Power/10KB jumbo frame/ 2xDIDO



Datasheet   Hardware Manual   Software Manual
For latest firmware, please send request to support@lantechcom.tw

OVERVIEW

Lantech IES-5408FM-PT is a high performance L2+ switch with 8 10/100TX + 4 100M Fiber that complies with IEC 61850-3 & IEEE 1613. It delivers ITU G.8032 enhanced ring recovery less than 20ms including dynamic coupling ring, and enhanced mode for easy configuration, comprehensive QoS, QoS by VLAN, advanced security including INGRESS/EGRESS ACL L2/L3, SSH/SSL, Mac based DHCP server, DHCP Option 82, DHCP server, IGMPv1/v2/v3/router port, QinQ* (double tag VLAN) which are important features required in train and large network. It also supports Cisco Discovery Protocol (CDP) and LLDP for Ciscoworks to detect the switch info and show on L2 map topology.


The exclusive GOOSE monitoring function (IEC packet) can display the counter of GOOSE message transmitted and received by port. The built-in MMS (Manufacturing Messaging Specification) server can help power SCADA to monitor and control switch by data modeling.


The IES-5408FM-PT also embedded several features for stronger and reliable network protection in an easy and intuitive way. When the pre-set ring configuration failed or looped by miss-wiring, Lantech IES-5408FM-PT is able to alert with the LED indicator and send out an email, traps or a SMS text. Repowered auto ring restore function (node failure protection) ensures the switches in a ring to survive after power breakout is back. The status can be shown in NMS when each switch is back. This feature prevents the broken ring and keep ring alive without any re-configuration needed. Loop protection is also available to prevent the generation of broadcast storm when a dumb switch is inserted in a closed loop connection.


DHCP option 82 and relay agent function (Port/Vlan based DHCP distribution) can offer the same IP address on port base or vlan base where there is need to replace the new device connecting to Lantech switches to avoid any network disruption. The built-in DHCP Option 82 server offers the convenience of policy setting on the switch. Mac based DHCP server function assigns an IP address according to its MAC address to include dumb switches in DHCP network.


The user friendly UI, innovative auto topology drawing and topology demo makes IES-5408FM-PT much easier to get hands-on. The switch also equips the RTC (real time clock) which can keep track of time always. The complete CLI enables professional engineer to configure setting by command line.


Lantech IES-5408FM-PT features enhanced G.8032 ring which can be self-healed in less than 20ms for single ring topology protection covering Multicast packets. It also supports various ring topologies that covers double ring, multi-chain (under enhanced ring), train ring, basic ring by easy setup than others. The innovative auto-Ring configurator (auto mode) can calculate owner and neighbor in one step. It supports MSTP that allows RSTP over Vlan for redundant links with 8/16* MSTI.


The configuration file of Lantech IES-5408FM-PT can be exported in text file so that it can be edited and configured back to switch with ease for mass deployment. The factory reset button can restore the setting back to factory default and built-in watchdog design can automatically reboot the switch when CPU is found dead.


QoS by VLAN can allow switch to tag QoS by VLAN regardless the devices acknowledge QoS or not in which greatly enhance the bandwidth management in a network.


The IES-5408FM-PT DIDO function can support additional open/close physical contact for designate applications besides Port / Power events, for example, DIDO function can trigger alarm if the switch was moved or stolen. In case of events, the IES-5408FM-PT will immediately send an email & SMS text message to pre-defined addresses as well as SNMP Traps out. It provides 2DI and 2DO while disconnection of the specific port was detected; DO will activate the signal LED to alarm. DI can integrate the sensors for events and DO will trigger the alarm while sending alert information to IP network with email and traps.


The environmental monitoring can detect switch overall temperature, voltage and current where can send the SNMP traps, email and SMS alert when abnormal.


The Lantech IES-5408FM-PT has two isolated power inputs from DC18~72V and HV model offers one isolated 90~305VAC/120~430VDC power supply. Featured with relay contact alarm function, the IES-5408FM-PT is able to connect with alarm system in case of power failure. The IES-5408FM-PT also provides ±4KV EFT, ±4KV surge and ±8KV contact / 15KV air ESD protections, which can reduce unstable condition caused by power line and Ethernet. It features high reliability and robustness coping with extensive EMI/RFI phenomenon, surge, inductive load switching environment usually found in substation, steel automation, mining and process control. Widely operational temperature capacity (standard model: -20°C~60°C / -E model: -40°C~75°C) ensures the IES-5408FM-PT runtime through the harsh environment.


*Future Release
**Optional
Note : Environmental monitoring is not available on HV models

FEATURES

  • System Interface/Performance
    • 8 10/100TX + 4 100M Fiber (Total 12 Ports Switch)
    • IEC-61850 & IEEE1613 Compliance
    • Dual isolated power input (18~72VDC) or one isolated 90~305VAC/120~430VDC (HV model)
    • Back-plane (Switching Fabric): 2.4Gbps
    • 16K MAC address table
    • Widely operational temperature capacity (standard model: -20°C~60°C / -E model: -40°C~75°C)
    • Fan less design
  • Goose monitoring for port counter of Goose message (IEC packets)
  • MMS server built-in for power SCADA monitoring/control
  • Provides EFT protection ±4K VDC for power line
  • Supports ±8K contact/ 15K air Ethernet ESD protection
  • 10KB Jumbo frame supported on all ports
  • User friendly UI, auto topology drawing, topology demo, complete CLI for professional setting
  • Enhanced G.8032 Ring protection in 20ms for single ring
    • Support various ring/chain topologies, including dynamic coupling ring
    • Enhanced G.8032 ring configuration with ease
    • Auto ring configuration(auto mode) for single ring
    • Ring covers multicast on different ports
  • LACP load balancing to distribute the load*
  • Built-in RTC (Real Time Clock) to keep track of time
  • Supports IEEE 802.1p Class of Service, per port provides 8 priority queues Port base, Tag Base and Type of Service Priority
  • IEEE 802.1d STP, IEEE 802.1w RSTP,802.1s MSTP VLAN redundancy
  • 4K 802.1Q VLAN, Port based VLAN, GVRP**, QinQ*
  • Supports IEEE 802.1ab LLDP, Cisco CDP; LLDP info can be viewed via Web/ Console/ LantechTM InstaConfig**/ LantechTM InstaView**
  • DHCP server / client / Port/Vlan based DHCP distribution / DHCP Option 82 supported
  • Mac based DHCP server to assign IP address that includes dumb switches in DHCP network
  • Bandwidth Control
    • Ingress packet filter and egress rate limit
    • Broadcast/multicast packet filter control
  • Relay alarm output system events
  • Miss-wiring avoidance
    • LED indicator
    • Email, traps, or SMS notification
  • Repowered auto ring restore
    • Ensure the switches in a ring to survive after power breakout is back
    • The status can be shown in NMS when each switch is back
  • TFTP/HTTP firmware upgrade; LantechTM InstaConfig** for multiple upgrade
  • System Event Log, SMTP Email alert, SMS mobile (text) and SNMP Trap for alarm support; 32 RMON counters
  • Security
    • SSL/SSH/INGRESS/EGRESS ACL L2/L3
    • Port Security: MAC address entries/Filter/MAC-Port binding
    • IP Security: IP address security management to prevent unauthorized intruder.
    • Management access control with priority
    • Login Security: IEEE802.1X/RADIUS
    • HTTPS for secure access to the web interface
  • Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application
  • Multicast static route for non- IGMP camera to prevent flooding; IGMP router port to assign query in ring and for reversed multicast video flow
  • Multicast VLAN registration* for metro video
  • IGMPv1,v2,v3 with Query mode for multi media; GMRP*
  • Factory reset button to restore setting to factory default
  • Watchdog design to auto reboot switch CPU is found dead
  • Optional environmental monitoring for system input voltage, current, ambient temperature
  • Supports DIDO (Digital Input/Digital Output)
  • IP30 metal housing with DIN rail and Wall-mount** design
*Future Release
**Optional
Note : Environmental monitoring is not available on HV models

SPECIFICATIONS

Hardware Specifications

Standards

IEEE802.3 10Base-T Ethernet
IEEE802.3u 100Base-TX
IEEE802.3x Flow Control and Back Pressure
IEEE802.3ad Port trunk with LACP
IEEE802.1d Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1s Multiple Spanning Tree
IEEE802.3ad Link Aggregation Control Protocol (LACP)
IEEE802.1AB Link Layer Discovery Protocol (LLDP)
IEEE802.1X User Authentication (Radius)
IEEE802.1p Class of Service
IEEE802.1Q VLAN Tag

Switch Architecture

Back-plane (Switching Fabric): 2.4Gbps

Transfer Rate

14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Ethernet / Gigabit Fiber port

CPU

Marvell 800Mhz

RAM

256M Byte

Flash

128M Byte

Mac Address

16K MAC address table

Jumbo frame

10KB on all ports

Connectors

10/100TX: 8 x ports RJ-45 with Auto MDI/MDI-X
100M fiber: 4 x SC/ST type connector for single-mode or multi-mode type fiber cable
RS-232 connector: RJ-45 type
Power & P-Fail connector: 1 x 6-pole terminal block

Network Cable

10Base-T: 2-pair UTP/STP Cat. 3, 4, 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)
100Base-TX: 2-pair UTP/STP Cat. 5/ 5E/ 6 cable
EIA/TIA-568 100-ohm (100m)

Optical Cable

125Mbps:
Multi mode: 0 to 2 km/ 5 km, 1310 nm (62.5/125 μm)
Single mode: 0 to 30 km, 1310 nm (62.5/125 μm)
WDM 125Mbps:
Single mode: 0 to 20 km/ 40 km/ 60 km/ 80 km, 1310 nm (9/125 μm); 0 to 20 km/ 40 km/ 60 km/ 80 km, 1550 nm (9/125 μm)

Protocol

CSMA/CD

LED

Per unit: Power 1 (Green), Power 2 (Green), Fault (Red), RM (Green)
Ethernet port: Link/Activity (Green), Speed (Green); Fiber: Link/Activity (Green)

DI/DO

2 Digital Input (DI) :
Level 0: -30~2V / Level 1: 10~30V
Max. input current:8mA
2 Digital Output(DO): Open collector to 40 VDC, 200mA

Operating Humidity

5% ~ 95% (Non-condensing)

Operating Temperature

-20°C~60°C / -4°F~140°F (Standard model)
-40°C~75°C / -40°F~167°F(-E model)

Storage Temperature

-40°C~85°C / -40°F~185°F

Power Supply

Dual isolated power input (18~72VDC) or one isolated 90~305VAC/120~430VDC (HV model)

Power Consumption

12W

Case Dimension

Metal case. IP-30,
74 (W) x 114 (D) x 152 (H) mm

Weight

900 g

Installation

DIN Rail and Wall Mount** Design

EMI & EMS

FCC Class A,
CE EN55022 Class A, CE EN55024, CE EN61000-4-2, CE EN61000-4-3, CE EN61000-4-4, CE EN61000-4-5, CE EN61000-4-6, CE N61000-4-8, EN61000-4-11

Stability Testing

IEC60068-2-32 (Free fall), IEC60068-2-27 (Shock), IEC60068-2-6 (Vibration), IEC60870-2-2, IEC60068-2-30

Power Automation

IEC 61850-3
IEEE 1613

MTBF

NA

Warranty

5 years

Software Specifications

Management

SNMP v1 v2c, v3/ Web/Telnet/CLI

SNMP MIB

RFC 1215 Traps MIB,
RFC 1213 MIBII
RFC 1158 MIBII
RFC 1157 SNMP MIB,
RFC 1493 Bridge MIB,
RFC 1573 IF MIB
RFC 2674 VLAN MIB,
Partial RFC 1757 RMON,
RFC 2674 Q-Bridge MIB; Bridge MIB,
LLDP MIB*
RSTP MIB*
Private MIB

ITU G.8032

Support ITU G.8032 v2/2012 for Ring protection in less than 20ms for self-heal recovery (basic mode)
Support various ring/chain topologies
Includes dynamic coupling ring
Enhanced G.8032 ring configuration with ease
Ring covers multicast on different ports

User friendly UI

  1. Auto topology drawing
  2. Topology demo
  3. Auto configuration for G.8032(auto mode) for single ring
  4. Complete CLI for professional setting

Port Trunk with LACP

LACP Port Trunk: 8 Trunk groups/Maximum 8 trunk members

LLDP

Supports LLDP to allow switch to advise its identification and capability on the LAN

CDP

Cisco Discovery Protocol for topology mapping

Environmental Monitoring

System status for input voltage, current and ambient temperature to be shown in GUI and sent alerting if any abnormal status

VLAN

Port Based VLAN
IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K, VLAN ID can be assigned from 1 to 4096.)
GVRP(256 groups)**, QinQ*, QOS QinQ*

IPv6/4

Present

Spanning Tree

Supports IEEE802.1d Spanning Tree and IEEE802.1w Rapid Spanning Tree, IEEE802.1s Multiple Spanning Tree

Quality of Service

The quality of service determined by port, Tag and IPv4 Type of service, IPv4 Differentiated Services Code Points - DSCP

Class of Service

Support IEEE802.1p class of service, per port provides 8 priority queues

QoS by VLAN

Tagged QoS by VLAN for all devices in the network

IP Security

Supports 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder.

Login Security

Supports IEEE802.1X Authentication/RADIUS

Port Mirror

Support 3 mirroring types: “RX, TX and Both packet”

Network Security

Support 10 IP addresses that have permission to access the switch management and to prevent unauthorized intruder.
802.1X access control for port based and MAC based authentication/MAC-Port binding
Management access control with priority
Ingress/Egress ACL L2/L3
SSL/ SSH for Management
HTTPS for secure access to the web interface
TACACS+* for Authentication

IGMP

Support IGMP snooping v1,v2,v3; Supports IGMP static route; 256 multicast groups; IGMP router port ; IGMP query; GMRP*

Static MAC-Port bridge

Static multicast forwarding forward reversed IGMP flow with multicast packets binding with ports for IP surveillance application

Bandwidth Control

Support ingress packet filter and egress packet limit.
The egress rate control supports all of packet type.
Ingress filter packet type combination rules are Broadcast/Multicast/Flooded Unicast packet, Broadcast/Multicast packet, Broadcast packet only and all types of packet.
The packet filter rate can be set an accurate value through the pull-down menu for the ingress packet filter and the egress packet limit.

RTC

Built-in Real Time Clock to keep track of time always

Flow Control

Supports Flow Control for Full-duplex and Back Pressure for Half-duplex

System Log

Supports System log record and remote system log server

SMTP/Text SMS

Supports SMTP Server and 8 e-mail accounts for receiving event alert; can send SMS text alert via mobile

Relay Alarm

Provides one relay output for port breakdown, power fail and alarm.
Alarm Relay current carry ability: 1A @ DC24V

Protection

  1. Miss-wiring avoidance
  2. Repowered auto ring restore
  3. Loop protection

SNMP Trap

Up to 10 trap stations; trap types including:

  1. Device cold start
  2. Authorization failure
  3. Port link up/link down
  4. DI/DO open/close
  5. Typology change(ITU ring)
  6. PoE ping failure
  7. Power failure
  8. Environmental abnormal

DHCP

Provide DHCP Client/ DHCP Server/DHCP Option 82/Port based&VLAN based DHCP distribution (DHCP relay agent)

Mac based DHCP Server

Assign IP address by Mac that can include dumb switch in DHCP network

DNS

Provide DNS client feature and support Primary and Secondary DNS server.

SNTP

Supports SNTP to synchronize system clock in Internet

Goose Monitoring

Show individual Goose TX / RX counter (IEC packets)

IEC 61850-9-4

Built in MMS server for data modeling for power SCADA

Firmware Update

Supports TFTP firmware update, TFTP backup and restore; HTTP firmware upgrade; LantechTM InstaConfig** for multiple upgrade

Configuration
upload and download

Supports text configuration file for system quick installation; Support factory reset button to restore all settings back to factory default

IfAlias

Each port allows an alphabetic string of 128-byte assigned as its own unique name via the SNMP or CLI interface

*Future Release
**Optional
Note : Environmental monitoring is not available on HV models

DIMENSION

DC model

HV model

ORDER INFORMATION

P/N Model name Description
8358-506 IES-5408F-SC-MM-PT-HV 4 100M-SC MM 2KM + 8 10/100TX L2 +Industrial Managed Switch w/ One isolated 90~305VAC/120~430VDC power supply;
-20°C to 60°C
8358-5061 IES-5408F-SC-MM-PT-HV-E 4 100M-SC MM 2KM + 8 10/100TX L2 +Industrial Managed Switch w/ One isolated 90~305VAC/120~430VDC power supply;
-40°C to 75°C
8358-507 IES-5408F-SC-SM-PT-HV 4 100M-SC SM 30KM + 8 10/100TX L2 +Industrial Managed Switch w/ One isolated 90~305VAC/120~430VDC power supply;
-20°C to 60°C
8358-5071 IES-5408F-SC-SM-PT-HV-E 4 100M-SC SM 30KM + 8 10/100TX L2 +Industrial Managed Switch w/ One isolated 90~305VAC/120~430VDC power supply;
-40°C to 75°C
8358-504 IES-5408FM-SC-MM-PT 4 100M-SC MM 2KM + 8 10/100TX L2 +Industrial Managed Switch w/ Dual isolated DC power input 18V~72V;
-20°C to 60°C; Environmental monitoring
8358-5041 IES-5408FM-SC-MM-PT-E 4 100M-SC MM 2KM + 8 10/100TX L2 +Industrial Managed Switch w/ Dual isolated DC power input 18V~72V;
-40°C to 75°C; Environmental monitoring
8358-505 IES-5408FM-SC-SM-PT 4 100M-SC SM 30KM + 8 10/100TX L2 +Industrial Managed Switch w/ Dual isolated DC power input 18V~72V;
-20°C to 60°C; Environmental monitoring
8358-5051 IES-5408FM-SC-SM-PT-E 4 100M-SC SM 30KM + 8 10/100TX L2 +Industrial Managed Switch w/ Dual isolated DC power input 18V~72V;
-40°C to 75°C; Environmental monitoring
8358-508 IES-5408F-ST-MM-PT-HV 4 100M-ST MM 2KM + 8 10/100TX L2 +Industrial Managed Switch w/ One isolated 90~305VAC/120~430VDC power supply;
-20°C to 60°C
8358-5081 IES-5408F-ST-MM-PT-HV-E 4 100M-ST MM 2KM + 8 10/100TX L2 +Industrial Managed Switch w/ One isolated 90~305VAC/120~430VDC power supply;
-40°C to 75°C
8358-509 IES-5408F-ST-SM-PT-HV 4 100M-ST SM 30KM + 8 10/100TX L2 +Industrial Managed Switch w/ One isolated 90~305VAC/120~430VDC power supply;
-20°C to 60°C
8358-5091 IES-5408F-ST-SM-PT-HV-E 4 100M-ST SM 30KM + 8 10/100TX L2 +Industrial Managed Switch w/ One isolated 90~305VAC/120~430VDC power supply;
-40°C to 75°C
8358-510 IES-5408FM-ST-MM-PT 4 100M-ST MM 2KM + 8 10/100TX L2 +Industrial Managed Switch w/ Dual isolated DC power input 18V~72V;
-20°C to 60°C; Environmental monitoring
8358-5101 IES-5408FM-ST-MM-PT-E 4 100M-ST MM 2KM + 8 10/100TX L2 +Industrial Managed Switch w/ Dual isolated DC power input 18V~72V;
-40°C to 75°C; Environmental monitoring
8358-511 IES-5408FM-ST-SM-PT 4 100M-ST SM 30KM + 8 10/100TX L2 +Industrial Managed Switch w/ Dual isolated DC power input 18V~72V;
-20°C to 60°C; Environmental monitoring
8358-5111 IES-5408FM-ST-SM-PT-E 4 100M-ST SM 30KM + 8 10/100TX L2 +Industrial Managed Switch w/ Dual isolated DC power input 18V~72V;
-40°C to 75°C; Environmental monitoring


OPTIONAL ACCESSORIES - DIN Rail Power

Model name Description
MDR-40 Series 40W Single Output Industrial Din Rail Power; 85-264VAC / 120-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 4% per degree from 60°C ~ 70°C)
MDR-20 Series 20W Single Output Industrial Din Rail Power; 85-264VAC / 120-370VDC Input Range; Cooling by free air convection; RoHS2 ; Operating Temp. -20°C~70°C (ambient, derating each output at 2.5% per degree from 50°C ~ 70°C)